The use for a portable CO2 meter is to be able to measure air quality in closed spaces (i.e. the office). The higher the number (usually above 1200~1500) the worst ventilation, which means higher chances to get
the Covid-19.

CO2 Meter Front View

With this is possible to know when is time to open the windows and ventilate.

It’s main guts are:

• Arduino Pro Micro, Leonardo Atmega32u4 based.
• SenseAir S8 LP CO2 sensor.
• Vintage HP HDSP-2000 ceramic LED matrix display, manufactured week 20 year 1984. NOS.

Back view of handmade CO2 meter

The capacitor stands for when the CO2 sensor does a read cycle (every 2s): both the display and the SenseAir S8 uses so much power that you can see the display and leds in the Arduino Pro Micro sighly dim off when powered from standard USB 0.5A when a read is made in the SenseAir CO2 Sensor. Without the capacitor, the arduino can’t stand for the display refresh and does a glitch in the display.

CO2 Meter glitch

Also there’s a UDN2981A source driver to drive the columns in the HDSP-2000 display and a small momentary press button with 10K pull down resistor to launch sensor callibration if pressed on powerup (use with caution!!).

CO2 Meter first working stage

The components that makes it portable are:

• Lithium battery charger (Like this one).
• Recycled Li-Po cell (250mAh)
• Pololu s7v8a adjustable step-up DC-DC (adjusted to 5V).
• Switch.

Making CO2 Meter porable with lipo charger and battery

I use the same components to make projects portables. The good thing about the pololu s7v8a is that it is both a step-up and a step-down DC-DC converter. This is handful if a project work 3.3v as it will give 3.3v always even if the battery is reading 3.0v. Unfortunally the recicled 250mAh battery is not much for the power needs so only lasts 30m on thi battery cell.

CO2 Arduino HDSP-2000 SenseAir Schematic

Code available here.

In the video the leds seems to be dimmer than they really are because of the high light, but actually they are pretty much visible.

Overall all makes a nice looking portable and easy to use CO2 meter and Covid prevention tool in closed spaces.

But to work, it needs external power supply. Either a USB-B cable or a 9v battery with a barrel plug. And I hate having external addons to make it work.

Arduino Enigma Machine with battery

So I put inside the case a lipo battery, a lipo charger and a 5v stepup to power up everything.

Mooltipass is not eligible to be associated to the guest OS

After some googling I found a relevant KB (knowledge base) article about associating HiD devices entirely to a Virtual Machine and disassociating it from the host OS: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1033435.

The article says that the virtual machine hardware definition file (.vmx extension, usually located at /Users/$USER/Documents/Virtual Machines.localized) has to be manually edited after shutting down the virtual machine and the VMware Fusion to add the two following lines:

usb.generic.allowHID = "TRUE"
usb.generic.allowLastHID = "TRUE"

After adding both lines, you can safely search for the Mooltipass HiD devide to properly associate it to the guest OS:

vmware_fusion_screenshot_with_usb_mooltipass

Sensor Board Main display Side Showing Ponglock

Feature list:

• I2C Bus to save pins for future use.
• 128×64 OLED I2C Display: let’s draw anything
• Momentary switch on left and cross plus center buttons on right (total 6 input buttons)
• Arduino Leonardo based: USB for anything.
• Temperature sensor (I2C)
• Barometer sensor (I2C)
• Accelerometer sensor (I2C)
• Real Time Clock (I2C) plus backup battery.
• Switched power supply.
• LiPo charger.
• Tiny design: let’s make portable projects.

Sensor Board Main Component Side

I couldn’t resist temptation.. I ported the pongclock code from Rob Parrett to this tiny board. Here is the result:

Hardware is open hardware, you can obtain anything on Mike’s web or you can buy it directly from Tindie. Custom pongclock code can be downloaded from here.

About 9 months ago one Hackaday reader dropped some comments about compiling the source I published here a year ago and some troubles. After that, Mike and me kept talking and things turn out that he was PCB developer, so we though we could make together GPS cube version for real.

Together we developed a schematic and Mike built all himself several prototypes until we finally came with a (almost!) final version. So, here we are, one year after first release:

GPS Cube version 2

This version has several features:

• Everything is packed together in a single board.
• Better GPS: we switched to MT3339 PA6H instead old SirfStar III EM-411
• We added TMP75 I2C temperature sensor.
• The display PCB is also custom to run 3.3v
• Everything runs 3.3v: GPS, display, FTDI, TMP75 and atmega328p is now running 8MHz, Battery lasts longer.
• Expansion header with SPI and I2C: the board ca be used as development board for any other projects with displays or GPS.

GPS Toy Hardware Rev1.0

New GPS Board back

All the hardware was designed and developed by Mike Rankin (probably will go to Tindie) meanwhile I developed the software.